LAYCOCK ELECTRIC MOTOR WINDING HEADS
 


At Laycock, we do our best to keep up with the trends in the industry and in ways to make winding easier. The results of this commitment are now available to you!

Laycock Systems produces a complete line of single and three phase random wound electric motor winding heads. All Laycock winding heads will fit on either of our 19" (48.3 cm) or 25" (63.5 cm) length holders with quick release. All winding heads are coated with high impact nylon for smoother operation and less wear and abrasion. Try this remarkable concentric coil winder product line today!



THREE PHASE WINDING HEADS

These three phase winding heads require one setting only and are similar to single phase winding heads. If you have the Laycock Holder, you just change winding heads for three phase coil winding. Measure the insulated slot length and width of coil span. Select the winding head width nearest the width of coil span. Place the heads on the holder, spaced apart the length of insulated stator slot and you are ready to wind!


 

THREE PHASE SET WITH HOLDER
 
 

Three Phase Set with Holder

(Part Numbers LA-300, LA-300-HR-19, or LA-300-HR-25)
 
 

The Easier Way of Laycock

  • Only requires one setting (length)
  • Saves as much as one inch (25.4 mm) of wire per turn
  • Coils require no taping - just tie the leads
  • Saves as much as one hour's time in winding
  • Heads fit on Laycock 19" (48.3 cm) or 25" (63.5 cm) holders
  • No corners to short out


Round coils without sharp corners may save as much as one inch (25.4 mm) of magnetic wire per turn. Multiply this by the number of turns and you will see how Laycock saves you money. You may also save as much as one hour's time!

Round coils will not short out as diamond shaped coils can so it is not necessary to tape the end turns. Just sleeve the leads and use phase insulation when required!

 
 

NEW LARGE THREE PHASE HEADS

 




HEAD #6
THREE PHASE
PART# LA-306
HEAD #8
THREE PHASE
PART# LA-308

                                                                                                                                                     
With Laycock products, you profit by our experience! These new winding forms will add versatility to your Laycock Winding Equipment.

Now, with deeper and wider slots to accommodate more wire for some of the new type motors. Slot depth is 11/16" (17.5 mm). These new sizes will wind motors up to 150 H.P. All heads fit either 19" (48.3 cm) or 25" (63.5 cm) Laycock holders with instant coil release.

 

NEW SMALL THREE PHASE HEADS 6 SLOT



NEW THREE PHASE HEADS
         Head # 0                 Head # 00                      Head # 000                  COMPARISON
         2" wide                   1 1/2" wide                     1" wide                              VIEW
         (50.8 mm)               (38.1 mm)                       (25.4 mm)

These 6 slot winding forms were developed to wind very small or very low speed three phase motors, as well as loom motors with short spans, small shaded pole fan motors and coils for bi-polar fields. The slot depth has been increased to 5/16" (7.9 mm)

As with all our wind heads, they mount on either our 19" (48.3 cm) or 25" (63.5 cm) Laycock holders and quick release.


NEW SMALL THREE PHASE HEADS 12 SLOT


 

This 12 slot winding form was developed to wind very small or very low speed three phase motors, as well as loom motors with short spans, small shaded pole fan motors and coils for bi-polar fields. The slot depth has been increased to 5/16" (7.9 mm)
 

COMBINATION SINGLE AND THREE PHASE HEADS WITH HOLDER

For the person just starting in business, this combination provides complete winding equipment for nearly all the random wound motors that come to a shop for repair - both single and three phase. Both sets mount on the same Laycock holder with quick release and will save on your initial  investment. You will save time and money as it is not necessary to change the holder - just change heads!

Combination consists of No. 1 through No. 11 single phase and No. 1 through No. 5 three phase heads with either 19" (48.3 cm) or 25" (63.5 cm) holder and instant coil release.

All Laycock Heads are coated with high impact nylon for smoother operation and less wear and abrasion. All dimensions listed are approximate.

Model #DescriptionPrice- US. DollarsPacking & HandlingWeight
Domestic Export
LA-12-300-000 #000  1"       WIDE HEAD   (THREE PHASE HEADS ARE 12-SLOT) *** Spreader Bar Must be Used $624.00 $10.00 $10.00 1Lbs
LA-12-300-00 #00  1 1/2"       WIDE HEAD   (THREE PHASE HEADS ARE 12-SLOT) *** Spreader Bar Must be Used $644.00 $10.00 $10.00 1Lbs
LA-300-000 #000  1"       WIDE HEAD   (THREE PHASE HEADS ARE 6-SLOT) $124.00 $10.00 $10.00 1Lbs
LA-300-00

#00  1 1/2"    WIDE HEAD   (THREE PHASE HEADS ARE 6-SLOT)

$124.00 $10.00 $10.001Lbs
LA-300-0 #0      2"       WIDE HEAD $124.00 $10.00 $10.001Lbs
LA-301 #1      2 1/2" WIDE HEAD $130.00 $10.00 $10.001Lbs
LA-302 #2      3 1/4" WIDE HEAD $142.00 $10.00 $10.002Lbs
LA-303 #3      3 3/4" WIDE HEAD $154.00 $10.00 $10.002Lbs
LA-304 #4      4 1/4" WIDE HEAD $166.00 $10.00 $10.003Lbs
LA-305 #5      5 1/4" WIDE HEAD $189.00 $10.00 $10.003Lbs
LA-306 #6      6 7/8" WIDE HEAD $266.00 $10.00 $10.008Lbs
LA-308 #8      8 3/8" WIDE HEAD $366.00 $10.00 $10.0010Lbs
LA-306-8 SET OF #6 & #8 THREE PHASE HEADS $596.00 $10.00 $20.0018Lbs
LA-300 SET OF #1 through #5 THREE PHASE HEADS (5) $744.00 $10.00 $20.0011Lbs
LA-300-HR-19 SET OF #1 THRU #5 THREE PHASE HEADS WITH STANDARD 19" LONG HOLDER & INSTANT COIL RELEASE $1,151.00 $20.00 $40.0020Lbs
LA-300-HR-25 SET OF #1 THRU #5 THREE PHASE HEADS WITH SPECIAL 25" LONG HOLDER & INSTANT COIL RELEASE $1,163.00 $20.00 $40.0021Lbs
LA-100-3-HR-19 COMBINATION SET OF #1-11 SINGLE PHASE AND #1-5 THREE PHASE HEADS WITH STANDARD 19" LONG HOLDER & INSTANT COIL RELEASE $2,272.00 $20.00 $40.0045Lbs
LA-100-3-HR-25 COMBINATION SET OF #1-11 SINGLE PHASE AND #1-5 THREE PHASE HEADS WITH SPECIAL 25" LONG HOLDER & INSTANT COIL RELEASE $2,284.00 $20.00 $40.0046Lbs
LA-HDSB-26 26" HD Holder Spreader Bar WITHOUT SCALE *** Use with 12 Slot Heads *** $186.00 $10.00 $10.00 -
LA-HD-RB QUICK RELEASE ADAPTER & BLOCK (for standard single phase and 3-phase heads to fit heavy-duty bar) $930.00 $10.00 $10.00 -

* Prices are subject to change without notice.
* Minimum Net billing of $ 75.00 plus Packaging and Handling fee

 

QUESTIONS OR COMMENTS?    EMAIL US AT laysys@verizon.net